<var id="gpqzg"></var>
<dfn id="gpqzg"></dfn>

<rp id="gpqzg"><thead id="gpqzg"></thead></rp>

  1. <b id="gpqzg"><address id="gpqzg"></address></b>
      <delect id="gpqzg"></delect><acronym id="gpqzg"><thead id="gpqzg"><tr id="gpqzg"></tr></thead></acronym>

        <var id="gpqzg"><td id="gpqzg"><object id="gpqzg"></object></td></var>
        歡迎來到山東創杰智慧裝備科技有限公司,我們竭誠為您服務
        工廠車間整體除塵設備的日常維護保養
        來源:http://www.hnbjyygs.com/ 發布時間:2023-07-19
        1、技術人員應了解車間整體除塵設備的基本原理,特性,應用標準,并熟練掌握調整和維修方式。
        1. Technicians should understand the basic principles, characteristics, application standards, and proficiently master the adjustment and maintenance methods of the overall dust removal equipment in the workshop.
        2、減速機,輸灰裝置等分子熱運動構件應按規定加油和換油,發覺有異常情況應及時排除。
        2. The reducer, ash conveying device and other molecular Thermal motion components shall be refueled and replaced as required, and any abnormal condition shall be eliminated in time.
        3、儲氣罐,氣源三聯件中的油水分離器應每組排污一次,同時油水分離器應每間隔3~6月清理一次,油霧器應時常查驗存油狀況,及時給油。
        3. The oil water separator in the air storage tank and air source triplet should be drained once per group, and the oil water separator should be cleaned every 3-6 months. The oil mist collector should regularly check the oil storage status and provide oil in a timely manner.
        4、電磁脈沖閥如出現故障,應及時地排除,如內部有殘渣,水份,應完成清除,如膜片損壞應及時拆換。
        4. In case of fault of Electromagnetic pulse valve, it shall be removed in time. If there is residue and moisture inside, it shall be removed. If the diaphragm is damaged, it shall be removed and replaced in time.
        5、應用按時式清灰控制板,應定時測量清灰周期是不是準確,不然應做好調整。應用定阻式脈沖控制儀,應按時檢查壓力開關的工作情況,測壓口是不是阻塞,并完成清除。
        5. When using a timely ash cleaning control board, it is necessary to regularly measure whether the ash cleaning cycle is accurate, otherwise adjustments should be made. When using a constant resistance pulse control instrument, the working condition of the pressure switch should be checked on time, the pressure tap should be checked for blockage, and the removal should be completed.
        6、按時測量工藝主要參數,如煙塵量,溫度,濃度值等,出現異常,應找到根本原因并妥善處理。
        6. Measure the main parameters of the process on time, such as smoke and dust amount, temperature, concentration value, etc. If any abnormalities occur, the root cause should be found and properly handled.
        車間整體除塵設備
        7、啟動時,應先接入壓縮空氣至儲氣罐,接入操縱電源,運行排灰裝置,假如系統中還有其他設備,應先運行下游設備。
        7. When starting, compressed air should be connected to the air storage tank, the control power should be connected, and the ash discharge device should be operated. If there are other equipment in the system, downstream equipment should be operated first.
        8、關機時,在工藝系統終止以后,應維持除塵設備和專業再次工作中一段時間,以除塵設備內的潮氣和粉塵。
        8. When shutting down, after the process system is terminated, the dust removal equipment and profession should be maintained in operation for a period of time to remove moisture and dust from the equipment.
        務必留意的是,在除塵設備停止工作時,務必不斷對除塵設備開展清灰(可以用手動式清灰),將除塵濾袋上的粉塵祛除,防止受潮氣危害而糊袋子。更多相關事項就來我們網站http://www.hnbjyygs.com咨詢吧!
        It is important to note that when the dust removal equipment stops working, it is necessary to continuously clean the dust removal equipment (manual cleaning can be used), remove the dust from the dust removal filter bag, and prevent the bag from being damaged by moisture. For more related matters, come to our website http://www.hnbjyygs.com Consult!

        上一篇:活性炭吸附塔的廢氣處理工作!
        下一篇:移動伸縮房的操作要注意哪些操作流程?

        • 服務熱線: 18563723072
        • 官方微信
        在线观看一级毛片免费,亚洲一区二区约美女探花,欧美在线免费,日韩在线二区全免费